How to Thread an Old Janome Sewing Machine

It’s not all that difficult to thread an old Janome sewing machine. It’s just a matter of figuring out how to do it.

How to Thread an Old Janome Sewing Machine

So here are the steps you need to follow in order to thread an old Janome sewing machine:

Step One

1) Turn the handwheel back and forth, which will pull up any slack you might have in your thread so that there is no chance for knots or tangles on the spool.

Step Two

2) Pull off about 18 inches of thread from the spool and cut it with scissors (make sure not to put your fingers near where you’re cutting).

Step Three

3) Thread one end of this new piece of thread through what is called a needle plate loop, which should be located at either side of the machine under the presser foot.

Step Four

4) Thread the other end of this new piece of thread through a hole on the pulley at one side of the sewing machine where other pieces of thread are already going or have been there before.

Step Five

5) Now you’re ready to pass the needle up through what’s called a bobbin case, which is located just below where your spool of thread is.

Step Six

6) And now you simply pull the bobbin case toward you so that it goes out of its slot and then grab a bobbin from the side and put it into place on top of this same balance case before pulling both ends through holes in the front.

Step Seven

7) When your bobbin is properly installed, pull up on the thread end and you should have a perfect stitch.

RELATED ARTICLES

How Do You Thread Janome Sewing Machine Needle

Janome 234 Review

How to Thread an Old Janome Sewing Machine Video Tutorial

How to Thread an Old Janome Sewing Machine FAQs

Are vintage sewing machines worth anything?

There are plenty of people who would argue that vintage sewing machines are worth the price if they can be fixed. They may be older, but they still have a lot of life left in them. This is why there are many sewing machine repair shops to help with these machines. If you’re a great vintage sewing machine repair person, then you may have considered the idea of owning your own shop.

How do you use an old sewing machine?

You can follow the steps in order to use an old sewing machine.

-Turn the handwheel back and forth to pull up any slack you may have on your thread from it being wound too tight.

-Pull off about 18 inches of thread from the spool and cut it with scissors.

-Thread one end of this new piece of thread through what is called a needle plate loop, which should be located at either side of the machine under the presser foot.

-Thread other ends of this new piece of thread through a hole on the pulley that connects to the stitch length control knob over at the right side where other pieces are going or were before.

-Now you’re ready to pass the needle through the bobbin case

Related Article: Janome 234 vs 2212

How old is my Janome Sewing Machine??

Janome sewing machines have a model number which is usually followed by three or four numbers. The first two digits indicate the year of manufacture. In general, Janome started the use of date codes in 1986 and began using 4 digit date codes from 1991 onwards.

If your machine has specific markings on it that state this then you can check the section  “Checking the Date Code” for more information.

The Janome sewing machine model number is usually stamped on a plate attached to the side of the machine.

This plate may have been removed or lost and if that’s the case then you can still tell how old your Janome sewing machine is by following these steps:.

Check the machine’s serial number.  Most Janome sewing machines have a 6 or 7 digit serial number under the foot of the machine. Some models also have an 8 digit serial number on a metal plate attached to the top of the machine.

Check for a date code or manufacturing code number marked onto the machine anywhere on the baseplate or body of your sewing machine: (This will only work if your machine has markings if it does not have these codes and you cannot find a serial number, you will need to refer to the section “Checking the Date Code”).

How do you tell it’s age?. If your Janome sewing machine was manufactured before 1982 then it would have been made in Japan.

The year of manufacture is indicated by a “0” followed by three digits i.e. 0002 for the year 2000, the last digit is a check digit and does not indicate any number.

You can also check that you are looking at an authentic Janome model by looking at the underside of your sewing machine.

Authentic Janome models will have an oval brass badge with “Janome” along the top and “Made in Japan” along the bottom, if this is missing or damaged then you may be looking at a counterfeit.

Here are some examples of these numbers: 00003 for 2003, 00084 for 1984, 00005 for 2005, and 00024 for 2002.

How do I thread a Janome limited edition?

How do you thread an old white sewing machine?

How do you thread a vintage good housekeeper sewing machine?

How do I thread a Janome My Excel 18w sewing machine?

Leave a Comment