Last Updated on 1 year by Susan Mayrich
Are you wondering about Janome sewing machine bobbin problems? Then, you are in the right place to know the significant issues and their solutions. There seem to be various bobbin problems, including the bobbin thread, case, tension, and any malfunctions part problem.

A sewing machine is a significant investment, and you must know how to take care of it for the machine to last as long as possible. Therefore, if you have a Janome sewing machine, you need to know about these issues to be prepared for them if they ever come up.
If the issue ends up being something small and you can fix it yourself, that’s great. This article will cover some common Janome’s sewing machine bobbin problems and solutions. So, let’s start reading this article and learn the fantastic solutions!
Janome’s Sewing Machine Bobbin Problems And Solutions
This sewing machine may have different problems, and you need to learn them carefully and understand Janome sewing machine bobbin problems. So, without further ado, let’s start reading!
#1. Janome bobbin thread is not catching
One of the most common bobbin problems is that the thread doesn’t seem to catch even if you are following the proper technique. The first thing that you should try is moving your bobbin to a different position on your machine. If it still doesn’t work, you should try replacing your needle with one new or sharpened one.
#2. Janome bobbin case jumping
The bobbin may be too close together, so the thread is caught up between them. You can fix this by adjusting the bobbin case or moving the bobbins apart. Your needle could be too long, so you need to replace it with a shorter one. Try winding the thread under tension when putting it in the bobbin case. This will also help keep your line from getting caught between your bobbins.
#3. Janome bobbin case lose
Janome’s sewing machine bobbin problems could arise when the bobbin case becomes loose after being threaded. First, you’ll need to take the bobbins out and then tighten them to ensure they’re in place. You can do this by following these instructions for your Janome machine: Locate the screw on either side of the bobbin case (it should be accessible without opening the machine). Turn the screw in a clockwise direction.
Test to ensure that it’s tight enough by running your fingers over the bobbin area. If it feels like there’s still any slack in the thread, you’ll need to thread the screw once more.
#4. Janome bobbin case assembly
The lower looper is a device that is used in a sewing machine. The primary role of this device is to take a thread from the spool and wrap it around the bobbin core. It does this using a special shuttle bobbin.
This is a cylindrical device that is found in many sewing machines. When the needle goes down, the lower looper comes into play. It then pulls it through due to the tension set up by the user. Another factor here is that this can also be done by another component called the bobbin winder.
This helps to wind thread onto the bobbin, which is also found in many sewing machines. One of the most common causes of lower looper malfunction is a build-up of lint and grease inside it. Other reasons may include that the lower looper is not moving at all or not catching threads when doing so. There are several ways in which you can resolve this.
Cleaning the machine is one option. Using heat to dissolve lint is another way that may work. If your lower looper still does not function, you will need to bring it to a repair shop or replace it.
#5. Stitches are skipping
If your stitches are skipping, this might be due to the pressure foot not being in place. You’ll need to make sure that it’s firmly engaged on the machine before you start stitching again.
#6. The machine is making a clicking noise
This could mean that the presser foot isn’t leveled with the surface of your fabric. To correct this, you’ll need to lower the presser foot until it touches the material and then turns the dial until it is in place.
#7. The machine is making a grinding noise
There are many reasons why your machine might make a grinding noise, and it could be for one of two reasons: There is either something stuck under the throat plate, or the throat plate isn’t in place properly. Something is stuck between the needle and the Presser foot, which will cause it to be off-balance. You can try removing whatever’s caught under there. First, you’ll need to open up the machine to clean out whatever is causing the problem.
#8. The sewing machine motor won’t turn on
If you’ve tried turning your sewing machine on and nothing happens, then there are probably a couple of things that could be wrong: The power cord isn’t plugged into the wall outlet. If this is the case, push it in. The switch may be broken, requiring a professional to fix it. If you’re not able to fix it yourself, call a local sewing machine repair place to get it fixed.
Why Does My Janome Sewing Machine Keep Jamming?
The most common cause of sewing machine jams is a build-up of grease and lint inside the needle case and bobbin case. Use an old toothbrush to clean the dirt from the control area, reassemble it, and try again. For those with a serger, use a small amount of oil on a paper towel or rag before inserting a new thread into the lower looper.
Oil also prevents jamming at the time of sewing at least once per month. Please take off your needle plate, then clean it thoroughly. Next, wipe on some new sewing machine oil either through the hole in the needle plate or open up one side of it slightly with your fingernail.
Why Is My Janome Sewing Machine Not Picking Up The Bobbin Thread?
You can solve Janome’s sewing machine problems. First, ensure that the sewing machine power cord is connected to an outlet and that the power button is in the ‘on’ position. Inspect the needle and make sure it’s not bent or dull; replace it if necessary. If you’re still having problems, check the hook that gathers thread from the bobbin case: make sure it’s catching and pulling the thread up to form a loop.
If not, try to raise and lower the needle manually to free any threads at its back. The solution to this problem, in most cases, is to clean the machine. If that doesn’t help, thread your needle up through the tension disc or thread guide.
Frequently Asked Questions (FAQs)
You can read some FAQs to get more information about sewing machine bobbins.
Why Is my bobbin thread jamming?
Several reasons could cause your bobbin thread to jam. Some common ones are that removing some of the material needs to be dealt with: A build-up of lint and grease needs to be dealt with. Due to a misfeeding or tensioning issue, the thread is not being pulled through the machine correctly. Your sewing machine is dirty and may need to be cleaned before continuing.
Why is my bobbin not moving?
The most common cause of a sewing machine’s lower looper not threading is because it has become jammed. It could also have been incorrectly threaded, or the needle is damaged and needs to be replaced. You can learn more solutions by visiting here: Janome sewing machine repair.
It’s A Wrap!
Finally! We have answered your question: Janome sewing machine bobbin problems. We have discussed various issues that can occur with your bobbin, but you don’t need to get panic. Follow the tips mentioned above and fix them to make things proper and active. Thank you, friends, for reading this article until the end. You may want to find out what is a bobbin and how to adjust bobbin tension on brother sewing machine.
None of these worked. I changed the needle, I took out the bobbin case and cleaned it. I reinserted the bobbin (multiple times), I rethreaded the machine (multiple times). It is not the thickness of fabric because I tried on differnt thickness of fabric. The bobbin thread keeps looping and jamming. The machine stops running. I bought this machine new and I have hardly used it, This is not the first time I have had this issue with this machine. I’m startingto hate the machine. I have sewed on my old machine for 48 years. I am not new to sewing.
Hi Luci
Maybe you should consider taking it for repair
I have had it in repair 3 times and the repair person just hands me a new bobbin case and tells me the one I was isung had BURRS on it from jammimg. He says that it will not work with the burrs but my question is… the burrs occur from the jammimg so something else has got to be wrong